Rod Repair/parts/material - Lures & Lure Making - New Brunswick Fishing

Jump to content


Photo

Rod Repair/parts/material


  • Please log in to reply
9 replies to this topic

#1 Monty

Monty

    Member

  • Members
  • PipPip
  • 21 posts
  • LocationNB

Posted 17 March 2012 - 01:32 AM

As i reequip/reorganize and prepare for the next outing...........

I have just come across again my interest in repairing a couple of rods from back in the day.I know some can relate to "out with the old and in with the new" but also hoping for knowledge and the understanding of having something meaningful, even if its not in use.One rod i have which is old and mostly reminds me of back in the day when being a kid and learning the outside world taking every bit of enjoyment in just being there. So as it sits aside and is unusable i often wondered why i don't repair it? I have come to see that this is not an easy task to get done or better yet get done properly. Over the years i have brought this subject up verbally with many meetings but the answer usually end up with "i don't know" I was close with some knowledge once learning that their is such a fine fiberglass sheet type that is used and naturally some kind of resin to make finish. Also heard of a gent that used to repair rods in the NB area that was good at it but no longer. I myself wonder even in the technique as i would even do the task myself but only when knowing 100% how and comparative options.

The other rod.....food for thought, is so different as i purchased it in Spain and when mailing it home as the airport would not let me bring it on the plane.They somehow broke a section and it as well is unusable. Being that the rod is 18Ft i was also hoping to change up on the guides?

All and all,use or put on the wall i sit and throw out there a topic that i feel should be rectified.

Maybe someday i could be that guy,anyone can come to for such a task?
  • 0

#2 Chadman

Chadman

    Advanced Member

  • Members
  • PipPipPip
  • 576 posts
  • LocationSouth Eastern New Brunswick

Posted 17 March 2012 - 02:43 AM

as far as getting rods repaired, I'd check with any of the local fly shops.. they'd probably be best to guide you to someone who can repair them.

also, next weekend, march 23 to 25, the fly fishing forum is at the moncton coliseum.. i have seen exhibotors there that repair fly rods.. there was one older guy that liked fixing bamboo rods.. not sure where you're located, but I think these are your 2 best options unless someone from the board posts up that they can fix them for you or share some knowledge so that you can repair them.
  • 0

#3 chnclr

chnclr

    Advanced Member

  • Members
  • PipPipPip
  • 105 posts
  • LocationMarysville NB

Posted 19 March 2012 - 08:54 PM

Monty I sent you a PM with reguard to repairing your rods.

  • 0
A man's gotta believe in something;I believe I'll go fishing

#4 Monty

Monty

    Member

  • Members
  • PipPip
  • 21 posts
  • LocationNB

Posted 19 March 2012 - 08:55 PM

Thank you for the reply Chadman.........i was hoping for something?
I did know of the show in Moncton coming and wondered what if?
Guess we'll see where this goes.
  • 0

#5 Monty

Monty

    Member

  • Members
  • PipPip
  • 21 posts
  • LocationNB

Posted 19 March 2012 - 08:56 PM

ok great but what is a PM?
  • 0

#6 casey hayward

casey hayward

    Advanced Member

  • Members
  • PipPipPip
  • 457 posts
  • LocationHopewell Cape

Posted 19 March 2012 - 09:11 PM

PM means private message which goes to your inbox and keeps your conversation private. Other members cannot seeit.
  • 0

#7 bucbug

bucbug

    Advanced Member

  • Members
  • PipPipPip
  • 67 posts
  • LocationHaneytown

Posted 20 March 2012 - 08:38 PM

We Fredericton Fish and Game offered Basic Fly Fishing Instruction. A One Day course on Saturday, 24 March 2012 from 9am until 3 pm. More at http://www.frederictonfishandgame.org/
  • 0

#8 Monty

Monty

    Member

  • Members
  • PipPip
  • 21 posts
  • LocationNB

Posted 29 September 2012 - 10:38 PM

Well food for thought.......not much being said towards rod repair from any one individual that can do the job so i'm going to revert with info or ideas towards tool's or material's when needing to do the job by self?
  • 0

#9 morfrost

morfrost

    Advanced Member

  • Members
  • PipPipPip
  • 113 posts

Posted 01 October 2012 - 07:08 PM

Since you didn't exactly specify what needed to be fixed it's kind of hard to give you specific details. Do you need to replace or rewrap guides? Is your rod shaft broken? Is the handle shot or the reel seat need to be replaced? Most of these repairs can be done by the rod owner quite easily.

I suggest Googling a specific question on a search engine. For example: " Replace broken guide on fishing rod" This should give you some specific information, likely with some UTube hits so you can see how it's done.

You can try your local Library. They may have a book by Boyd Pfeifer or Dale Clemens on fihing tackle, rod repair or rod building. This should give you some opportunity to borrow a book and learn about this and figure out how it applies to your needs. I know the Moncton Library has both of these authors. and they should be available from Provincial inter- library sevices.

If you need parts, search the internet..

The secrets are out there waiting to be discovered.
  • 0

#10 Monty

Monty

    Member

  • Members
  • PipPip
  • 21 posts
  • LocationNB

Posted 21 February 2013 - 10:29 PM

very nice Morfrost.....i will be looking into this! My tip has since broke off so it needs to be replaced. Figured i would just replace with a tip guide seeing its only 2" down. My main brake is in a middle section of my extended rod shaft (7 Meters) which has 6 pull outs. On top of fixing the section i wished to redo all the guides and re-wrap with a stronger guide. The pole came from Europe and is quite different from anything around here. I tried finding the manufacture but came up with nothing? Just thought with the work i wish to put into the rod to make finished........might as well do it up right and help or work on others to make it a possible fix
  • 0




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users